Realme 13 Pro+ RMX3921 (Stock ROM) Flash File

 

Realme 13 Pro+ RMX3921 Flash File used for flash and unlock your device fix pattern lock, FRP and other problems like hang on logo, brick after software update or in any experiment , fix hanging issue and other software related issues. Realme flash tool required login credential to run, if you don’t have then contact me for flash. it’s paid service. Always use latest flash file to flash your device.

Download Realme 13 Pro+ RMX3921 FLASH FILE

RMX3921export_11_14.1.0.630EX01_2024102214470000

ALL DRIVER FREE DOWNLOAD

PAID FILE

 

Reseller India

———————–
Ramzan Gsm
Gsm Online Services
Country : India
WhatsApp, https://wa.me/919036266587
Call +919036266587
Website : https://www.ramzangsm.com/

ALL MOBILE FLASHING UNLOCKING HANG ON LOGO FIX

SERVICE AVAILABLE VIA ULTRA VIEWER / TEAM VIEWER

 

ABOUT: Realme 13 Pro+ RMX3921

 

The Realme 13 Pro+ (model RMX3921) is a high-end smartphone that was announced in July 2024 and released on August 6, 2024.

Display and Design:

• Screen: 6.7-inch AMOLED display
• Resolution: Full HD+
• Refresh Rate: 120Hz
• Build: Corning Gorilla Glass 7i protection

Performance:

• Processor: Snapdragon 7s Gen 2 chipset
• RAM Options: 8GB or 12GB
• Storage Options: 256GB or 512GB

Camera System:

• Rear Cameras:
  • Primary: 50MP main sensor
  • Secondary: 8MP sensor
  • Tertiary: 50MP sensor
• Front Camera: 32MP sensor

Battery and Charging:

• Battery Capacity: 5,200 mAh
• Charging: Supports up to 80W wired charging; does not support wireless charging

Operating System:

• OS: Android 14 with Realme UI 5.0

 

Warning:

Flashing your device will erase all data. Backup your important data before proceeding.

Ensure you are using the correct firmware for your device to avoid bricking it.

 

—

Requirements

1. MSM Download Tool
Download the appropriate version for Realme 13 PRO+ .

2. Firmware File
Obtain the correct official firmware for the Realme 13 Pro+ RMX3921.

3. Qualcomm USB Drivers
Install Qualcomm drivers to allow your computer to detect the device in EDL (Emergency Download Mode).

4. USB Cable
Use the original or a high-quality USB cable.

5. Windows PC
The MSM Tool only works on Windows.

—

Steps to Flash Realme 13 Pro+ RMX3921:
1. Install Required Drivers

Install the Qualcomm USB drivers on your PC.

Restart your computer after installation.

2. Download Firmware and MSM Tool

Extract the firmware and MSM Download Tool files into a folder.

3. Put Device in EDL Mode

Turn off the device.

Press and hold Volume Up + Volume Down buttons together.

Connect the device to the PC via a USB cable while holding the buttons.

4. Open MSM Download Tool

Launch the MSM Download Tool as an administrator.

Enter the credentials (if required). Usually, “oppo” or “realme” is used as the password.

5. Load the Firmware

In the MSM Download Tool, click on the Load Firmware button.

Navigate to the extracted firmware folder and select the correct .ofp file.

6. Detect Device

Ensure your device is detected in the tool. It should appear as a COM port (e.g., COM3 or COM4).

7. Start Flashing

Click the Start button in the MSM Download Tool.

Wait for the process to complete (this may take 5-10 minutes).

Once completed, you will see a “Download Complete” message.

8. Reboot Device

Disconnect the device and power it on.

—

Troubleshooting Tips:
Device Not Detected:
Check if the Qualcomm drivers are properly installed. Use another USB cable or port if necessary.

MSM Tool Error:
Ensure the tool matches your device model and firmware. Disable antivirus temporarily as it may block the tool.

Boot Loop After Flashing:
Perform a factory reset by booting into recovery mode.